[ Pobierz całość w formacie PDF ]
.Luxalon® Aerofoils Fixed SystemLuxalon® Aerofoils Fixed SystemProduct:Luxalon® Aerofoils 200AF-450AFSystems:Fixed systemType:Aluminium extruded fin-shaped Aerofoils:200AF; 250AF; 300AF; 350AF; 400AF and 450AFWidth x height (mm):200x45; 250x51; 300x56; 350x60; 400x63; 450x66Size:Length______(max.span depending on wind load and fin type).Standard stock length is 7250 mm.Other lengths available onrequest.Minimum wall thickness:Aluminium extrusion minimum 2 mmAlloy extrusions:Al-Mg-Si 0.5 F22 (EN 755-2-6063-T66)Distance between Aerofoils:______mm (to be calculated or defined by specifier)Aerofoil angle fixed:______degrees (in steps of 5 degrees, to be calculated or definedby architect or client)End caps:Aluminium, following Aerofoil shapeFixations:With Luxalon® Aerofoil proprietary click-in sliding U-profiles andplastic fixation disks and fin-suspension connector (GF PA6).Stainless steel suspension boltFastening materials:All materials to be stainless steel in either A2 (304) or A4 (316)quality (to be specified by architect)Surface treatment:lWithout (mill finish)llNatural anodised in 20 or 25 micron thickness: VB6/A20 orlA25/VOM 1, in accordance with ISO 10546-93lOne layer polyester powder-coated; 60 micron, glossllevel______(std = 70%)lTwo layer polyester powder-coated; 90 micron, glossllevel______(std = 70%)lTwo or three layer PVDF powder-coated; 30 or 40 micron, glossllevel______(std = 70%)Colour:According to RAL standard colour card or any other standard,provided that a colour sample is availableSupporting structure:Steel or aluminium structure (not included in HD contract unlessspecifically requested).Structure to be sufficiently strong andsuitable to support occuring loads.Contact between mild steeland aluminium to be avoidedLuxalon® Aerofoils Adjustable SystemProduct:Luxalon® Aerofoils 200AF-450AFSystems:Adjustable systemType:Aluminium extruded fin-shaped Aerofoils:200AF; 250AF; 300AF; 350AF; 400AF and 450AFWidth x height (mm):200x45; 250x51; 300x56; 350x60; 400x63; 450x66Size:Length______(max.span depending on wind load and fin type).Standard stock length is 7250 mm.Other lengths available onrequest.Minimum wall thickness:Aluminium extrusion minimum 2 mmAlloy extrusions:Al-Mg-Si 0.5 F22 (EN 755-2-6063-T66)Distance between Aerofoils:______mm (to be calculated or defined by specifier)Aerofoil angle adjustable:Adjustable over 120 degreesEnd caps:Aluminium, following Aerofoil shapeFixations:With plastic bearing blocks, stainless steel (304) axle andsuspension bolt.Stainless steel endcap-connectors and drivingrodFastening materials:All fastening materials to be stainless steel in either A2 (304) orA4 (316) quality (to be specified by architect)Surface treatment:lWithout (mill finish)llNatural anodised in 20 or 25 micron thickness: VB6/A20 or A25/VOM 1, in accordance with ISO 10546-93 one layerllPolyester powder-coated; 60 micron, glossllevel______(std = 70%)lTwo layer polyester powder-coated; 90 micron, glossllevel______(std = 70%)lTwo or three layer PVDF powder-coated; 30 or 40 micron,lgloss level______(std = 70%)Colour:According to RAL standard colour card or any other standard,provided that a colour sample is availableSupporting structure:Steel or aluminium structure (not included in HD contract unlessspecifically requested).Structure to be sufficiently strong andsuitable to support occuring loads.Contact between mild steeland aluminium to be avoidedOperating system:lInternalllExternalllManualllElectric linear actuator 220V/50Hz or 380V/60HzllIndividual operation ______bays / ______floors / ______façadesllAutomated control systemlElectric wiring:Electric wiring is not a part of HD scope of works (to be supplied and connected by specialist contractor)
[ Pobierz całość w formacie PDF ]
